Handheld Printer TerminalUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Printer Terminal.Series
E-8• This guide does not include any information about programming and downloadprocedures. See the applicable separate documentation for information a
E-9GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (notapplicable to other areas).NOTICEThis equipment has been tested and found
E-10L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :(1) il ne doit pas produire de brouillage et(2) I’utilisateur du
E-11ContentsSafety Precautions ...E-1Operating Precautions ...
E-12Using the Bridge Satellite Cradle (HA-B61IO) ... E-49General Guide ...
E-13Be sure to perform the following steps before trying to use the Handheld PrinterTerminal for the first time.1. When unpacking, make sure that ever
E-143. Load the battery pack into the Handheld Printer Terminal.1 Turn the battery pack cover lockswitch on the side of the HandheldPrinter Terminal t
E-15Handheld Printer Terminal System ConfigurationOptionsRequired AC Adaptor for Bridge Satellite Cradle /Cradle-type Battery ChargerAD-S42120BECradle
E-16Handheld Printer Terminal System ConfigurationBattery PackDT-9723LICPaper Holder*HA-B93PHSplash Protect Cover*HA-B92PCVAC Cord for EuropeAC-CORD-E
E-17AD-S10095AEAD-S10095AUScreen Protect Cover*HA-B90DCVCablesDT-887AXA Dsub 9-Pin (Female) RS-232C Cross Cable for BridgeSatellite CradleDT-888RSC RS
• This Product is equipped with the Brycen B-RAPPORE Stack and My WirefreeNetwork Bluetooth User Interface Application, the use of which is governed b
E-18General Guide2534567891012241112131415161718231920182122IT-3100*The above illustrations show a model with C-MOS Imager andMagnetic Card Reader ins
E-191SD Memory Card Slot2Program Key (L)3 Roll Paper Holder4 Splash ProtectCover and PaperCutter5Power Key6 Indicator 1(Left Side)Indicator 2(Right Si
E-20General Guide15 Battery PackCover Lock Switch16 Battery PackCover17 PC Card Slot18 Hand Strap Hook19 14-pin SerialInterfaceConnector20 Power Termi
E-211 Fn Key2 Numeric Keys3 (Cursor Key)4 (Cursor Key)5-6.7C8BS9 ENTThis key is used to switch the character input mode or makevarious settings in co
E-22Replacing the BatteryYour Handheld Printer Terminal uses two types of battery: a battery pack and a memorybackup battery.A battery pack (DT-9723LI
E-23To replace the battery pack1. Make sure that the Handheld Printer Terminal is turned off.If the power is on, press the power key to turn it off.2.
E-24Important!• When replacing the battery pack, make sure you do not leave the HandheldPrinter Terminal without a battery pack for more than about 10
E-25A flexible hand strap can be attached to the Handheld Printer Terminal.Hook AHand StrapHook BAttach the hand strap following the procedure describ
E-26A neck strap can be attached to the Handheld Printer Terminal to keep it from beingdropped while being carried. The stylus holder provided can al
E-27Removal Procedure1. Pull back the locking bar of the neckstrap mounting hook and then releasethe hook from each ring as shown in theillustration.2
E-1Congratulations upon your selection of this CASIO product. Be sure to read thefollowing Safety Precautions before trying to use it for the first ti
E-282. Remove Mounting Hook C.3. Pass the stylus holder through the strapas shown in the illustration.4. Fold back the strap after passing throughBrac
E-29Calibrating Touch Screen AlignmentWhenever you feel that touch screen response is poor or that the operations beingexecuted do not match the locat
E-30Adjusting Display ContrastPerform the following steps to adjust display contrast to make display colors more vividand easier to see.• Press the “F
E-31The printer can print on roll paper (80 mm or 58 mm wide)* or 80 mm wide formedsheet paper. When printing on formed sheet paper, use the paper ho
E-32Using the Printer5. Close the roll paper holder, slide thelock knobs on the left and right sides asshown in the illustration to align at the“LOCK”
E-33Attaching the 58 mm Paper Width AdjusterAttach the 58 mm Paper Width Adjuster* inside the roll paper holder when using 58mm wide roll paper. Refe
E-34Using the PrinterWhen Using Formed Sheet PaperAttaching the Paper HolderAttach the separately sold Paper Holder (HA-B93PH)* when printing on forme
E-355. Loosen the two screws shown in theillustration (the screws cannot beremoved off).6. Open the cover (PC card slot cover) asshown in the illustra
E-36Using the Printer10. Fasten Part A of the Paper Holder tothe Handheld Printer Terminal.Press both ends of Part A to fasten tothe Handheld Printer
E-37Loading Formed Sheet PaperEnable the Auto Loading function by selecting Start, Settings, Control Panel and then“Printing Control” of Printer Setti
E-2Safety PrecautionsWarningDust and Moisture• Though the Handheld Printer Terminal is dust and water splash resistant, itsoptions including the batte
E-38Using the PrinterPrecautions When Using PrinterPrinting Accuracy1. During high-duty printing such as printing horizontal lines or printing while t
E-39Others1. The temperature range for printing with 2-ply paper and label paper is 5 to35°C.2. Once the end mark of the paper appears, promptly repla
E-40Using the C-MOS Imager(IT-3100M55E/IT-3100M55U/IT-3100M56E/IT-3100M75E only)1. Turn on the Handheld Printer Terminal, position its C-MOS Imager re
E-41• This label is a warning label for Class 2 laser products that comply withIEC60825-1+A2:2001CAUTION• Use of controls or adjustments or performanc
E-42The Magnetic Card Reader comes as standard with IT-3100M54E/M55E/M55U/M75E.Only use cards that are compatible with the ISO standards. The procedu
E-43IR CommunicationIR communication can be used to transferdata between two Handheld PrinterTerminals.When performing IR communication,orient the IR
E-44Bluetooth® CommunicationBluetooth® protocol can also be used totransfer data between two HandheldPrinter Terminals.The two Handheld Printer Termin
E-45Resetting the Handheld Printer Terminal is the same as restarting a computer.Performing a reset causes all unsaved inputs and edits to be lost, bu
E-46Performing a Full Reset (Initialization)Performing a full reset initializes memory. This means that all data stored in thememory (RAM) is deleted
E-471. TerminalModel: IT-3100M53E, IT-3100M55E, IT-3100M55U, IT-3100M54E,IT-3100M56E, IT-3100M75ECPU: Marvell® PXA255 Application Processor (400 MHz m
E-3CautionPrinter• Do not touch the areas around the printer motor or head since they canbecome very hot. Doing so can cause burns.• Touching any of
E-48Character Fonts: Kanji 12-dot 48/32 columns, 16-dot 36/24 columns, 24-dot 24/16columns (columns shown for 80 mm wide paper and 58 mm wide paper,re
E-49BackBottomRightTo pFrontThe optionally available Bridge Satellite Cradle (HA-B61IO) makes it possible totransfer system data and file data between
E-50Using the Bridge Satellite Cradle (HA-B61IO)1 System StatusIndicator Lamp2 CommunicationIndicator Lamp3Power IndicatorLamp4Terminal DetectSwitches
E-51Connecting the AC Adaptor and Connecting to a ComputerUse the AC adaptor available as an option for the Bridge Satellite Cradle to supply thepower
E-52Using the Bridge Satellite Cradle (HA-B61IO)4. Turn on the power. This causes the Bridge Satellite Cradle power indicator lamp tolight red.5. Plac
E-53Configuring DIP Switch SettingsRemoving the bottom cover of the Bridge Satellite Cradle exposes the DIP switches.You can change the ON/OFF setting
E-54Using the Bridge Satellite Cradle (HA-B61IO)Connecting Multiple Bridge Satellite Cradles (HA-B61IO)Connect “C-OUT” of the Bridge SatelliteCradle c
E-55Model no. of ACAdaptor Area/Region ComplianceAD-S42120BE All except China Compliant with CE,UL, FCC, and EnergyEfficiency Standards.AD-S42120BE-CN
E-56The optionally available Cradle-type Battery Charger (HA-B30CHG) lets you chargethe Handheld Printer Terminal’s battery simply by placing the Hand
E-571Power IndicatorLamp2Terminal DetectSwitches3Power Contacts4Power Switch5AC Adaptor JackThis lamp indicates the power status and the mounting stat
E-4Safety PrecautionsLithium-ion Battery PackDanger• Never use the Handheld Printer Terminal and its option including the batterypack and battery next
E-58Using the Cradle-type Battery Charger (HA-B30CHG)Connecting the AC Adaptor for the Cradle-type Battery ChargerUse the dedicated AC adaptor for the
E-59Cradle-type Battery Charger (HA-B30CHG) Specifications1. ChargingCharging System: Fixed-voltage (with current limiter)Charge Time: Approximately 8
E-601. Turn off the power of the HandheldPrinter Terminal by pressing the powerkey.2. Open the jack cover ( ), and theninsert the plug of the AC A
E-61Specifications1. Charging SpecificationCharging Method: Constant current/voltageCharge Period: Approx. 8 hours (with the power off)2. AC AdaptorMo
E-62PC card compatible with the PCMCIA(Type I/II) standard can be installed in the PCCard slot on the Handheld Printer Terminal. Insert a PC card acc
E-634. Open the cover (PC card slot cover) asshown in the illustration.5. Insert a PC card having PC card removaltape attached. Insert the PC card al
E-64Using PC CardsRemoving a PC CardPress the eject button on the left side of PCcard slot with the stylus as shown by thearrow, and pull out the PC c
E-653. After pushing on both ends of Part Aand reattaching to the Handheld PrinterTerminal ( ), remove Part B byremoving the screws ( ).4.Inse
E-667. While spreading apart both ends of Part A( ), remove Part A from the HandheldPrinter Terminal by lifting up Part A untilthe projections rea
E-6712SD memory card can be installed in the SD Memory Card slot on the Handheld PrinterTerminal. Insert (or remove) an SD memory card according to t
E-5Power Supply / AC AdaptorWarning•Do not use the Handheld Printer Terminal at a voltage other than thespecified voltage. Also, do not connect the Ha
E-68Connect a bar code reader to the RS-232C interface connector (8-Pin) on the HandheldPrinter Terminal.Connecting the bar code reader1. Check that t
E-69Attaching the Screen Protect Cover to the Handheld Printer Terminal prevents thescreen from being cracked or damaged when carrying.1. Remove the t
E-70Attaching the Splash Protect Cover to the Handheld Printer Terminal lets you use iteven during inclement weather.Attach the Splash Protect Cover b
E-715. Close the roll paper holder, slide thelock knobs on the left and right sides asshown in the illustration to align at the“LOCK” position to lock
E-72Important!• Make sure to attach the contact cover provided when removing the Battery Packfrom the Handheld Printer Terminal and storing.• If the b
CASIO COMPUTER CO., LTD.6-2, Hon-machi 1-chomeShibuya-ku, Tokyo 151-8543, Japan
E-6Safety PrecautionsBackup Copies of All Important DataCaution• Note that CASIO Computer Co., Ltd. shall not be held liable to you or anythird party
E-7Your Handheld Printer Terminal and its options are precision digital instruments.Improper operation or rough handling can cause problems with data
Comments to this Manuals