Casio EX-S770D Specifications

REX-S770DDivX correspondenceNOV. 2006(without price)INDEX

— 8 —2. How to restore the firmware1. Prepare the firmware restoration program and change its name as follows;rom837f-gm11.lbn 씮 saturn.binNOTE: This

— 9 —3. To install the firmwareInitially, firmware is not installed in the PCB supplied by the parts center.Install the firmware into the PCB after re

— 10 —ADJ TOOL IntroductionMake sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unitor the PCB.Here the ne

— 11 —7) Check “Designate the place to search”, designate the place which contains “inf” file in the driver bypressing “Reference” button, and then pr

— 12 —2. How to use ADJ Tool when replacing Lens unitMake sure to perform the following procedure after replacing the lens.A floppy disk with the lens

— 13 —3. How to use ADJ Tool when replacing MAIN PCBFirmware is not installed in spare parts.1 Enter the TEST mode.1. Turn the power on while pressing

— 14 —VCOM DC ADJUSTMENT PurposeReadjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. Necessary tools1

— 15 — Procedure1. Camera settinga) Turn the power on while pressing “BS” and “UPPER”.After pressing “DOWN” key twice, press “BS” and “MENU”.Select

— 16 —3. Measurementa) Connect S2281-01 to the camera’s LCD monitor (see below).AC Waveforms appear on the monitor screen of the oscilloscope.* Change

— 17 —THE COUNTERMEASURE FOR "SYSTEM ERROR"System error may occur when the battery is removed while data is written to the internal memory.

CONTENTSSPECIFICATIONS ...

— 18 —RESETTING THE PLACE OF DESTINATIONWhen the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required

— 19 —Screws (S1)C-CASE-BA3. Remove two screws and then remove C-CASE-CA.C-CASE-CAScrews (S1)4. Remove one screw and then remove C-CASE-ASSY.Screw (S3

— 20 —6. Remove the rear panel.Attention: The power button and the shutter button come off together. Be sure not to lose them.Screws (S2)Screws (S4)S

— 21 —8. Remove the strap board.Strap board9. Remove the REC SUB ASSY and the DATA SUB ASSY.* Fixed with double-sided tape.REC SUB ASSYDATA SUB ASSY*

— 22 —10. Release the lock and remove two FPCs.11. Remove two hooks and then remove the lens unit.FPCs* Hooks are located at three locations as below.

— 23 —12. Remove the tape fixing the FPC(LCD).13. Release the lock and remove one FPC.14. Remove the tape.15. Unsolder to remove two lead wires.Lead w

— 24 —16. Remove the LCD unit.* Fixed at three locations with double-sided tape.17. Remove one screw and then remove the battery case.18. Remove the t

— 25 —20. Remove the tape.21. Release the lock and remove two FPCs.22. Remove one screw.Screw (S5)23. Unsolder to remove three lead wires.24. Remove t

— 26 —26. Remove the key FPC.* Fixed with double-sided tape.27. Remove the shutter plate.Key FPCShutter plate28. Remove the TRIPOD ASSY.

— 27 —29. Remove the strobe assy.* Fixed with four hooks.Strobe assy30. Remove the strobe assy.* Fixed with three hooks.12Strobe case assy

— 1 —SPECIFICATIONSImage Files Format Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File System) 1.0 standard;DPOF compliantMovies: MPEG

— 28 —ASSEMBLY1. Set the strobe case assy.* Fix it with three hooks.2. Set the strobe assy.* Fix it with three hooks.Strobe assyStrobe case assy3. Rem

— 29 —6. Set the key FPC.There are eight pins as your positioning guide.Follow the assembling order as below.5. Set the LCD.* Fix it with a double-sid

— 30 —7. Solder two LCD lead wires.8. Tape on the lead wires.Lead wire (white)Lead wire (black)9. Set the battery case with one screw.Buttery case10.

— 31 —13. Solder three power lead wires.11. Solder two speaker lead wires.12. Tape on the lead wires.Lead wire (blue) Lead wire (gray)Lead wire (yello

— 32 —Lens unitHooks16. Set the lens unit.* Fix it with three hooks.17. Connect two FPCs of the lens unit.18. Set the REC sub assy and the DATA sub as

— 33 —(1) Attach the 4 pieces of double-sided tape and remove the protective stickers.Double-sided tapeDouble-sided tape(2) Fit the defective lens int

— 34 —20. Set the front panel.21. Set the strap board.Strap board(4) Take the front panel assembly off the defective lens.(5) Press on the conductive

— 35 —screws (S2)screws (S4)screw (S4)screw (S3)24. Assemble with six screws.22. Set the power button the shutter button.23. Set the rear panel.

— 36 —Screw (S3)25. Set the C-CASE-ASSY with one screw.C-CASE-ASSY26. Set the C-CASE-BA with two screws.27. Set the C-CASE-CA with two screws.C-CASE-C

— 37 —EXPLODED VIEW87S4S121383534S142S241S34036S310193011935137272139121417203343S5S4162422S623214444S41815162928263245S1S2S13126259134

— 2 —Delete1 file; all files (with memory protection feature)Effective Pixels7.2 millionImaging Element1/2.5 square pixel primary color CCD (Total pix

— 38 —PARTS LIST1 EX-S770D_SILVER-EUQTY11 10252942 CASE ASSY/CENTER TK-RJK509311*001 1 BB C2 10251069 SHUT-BUTTON/SHUT/A RJK509270-001V01 1 AF C3 1023

— 39 —1 EX-S770D_SILVER-EUQTY1S1 10203893 SCREW RJK502836-011V01 4 AA XS2 10226146 SCREW RJK508552-001V01 2 AA XS3 10254784 SCREW RJK502836-015V02 2 A

— 40 —PRINTED CIRCUIT BOARDMAIN PCB (TOP VIEW)FU101FU100

— 41 —MAIN PCB (BOTTOM VIEW)

CASIO COMPUTER CO.,LTD.Overseas Service Division 6-2, Hon-machi 1-ChomeShibuya-ku, Tokyo 151-8543, Japan

— 3 —• Battery: NP-20 (Rated Capacity: 700 mAh)• Recording Medium: SD Memory Card• Measurement Conditions*1 Number of Shots (CIPA)In accordance with C

— 4 — Rechargeable Lithium Ion Battery (NP-20)Rated Voltage 3.7 VRated Capacitance 700 mAhOperating Temperature 0 to 40°C (32 to 10 4°F) Dimensions 33

— 5 —BLOCK DIAGRAM2.8"-WIDE LCD7-LED BLLCD/BLKEY Flexible-board DISPMOVIE MENUBSLEFT SETUPDOWNRIGHTStrobeWIDESHUTTERPOWERTELEDATERECPLAYLenz-Uni

— 6 —TEST MODENote: Never perform the menu items unless otherwise instructed. Doing so may cause destruction ofthe data inside, which will make the ca

— 7 —PROGRAM VERSION UPGRADING1. To update the firmware version1. Prepare the memory card which contains the firmware for EX-S770D in the root directo