Casio XW-P1 User's Guide download pdf (Page 39)

Selecting and Creating Tones

E-37

To change the pitch in octave steps, use the

OCTAVE minus (–) and plus (+) buttons

(without holding down

TRANSPOSE).

• The setting range for this operation is three octaves

upwards and downwards (–3 octaves to +3 octaves).

• While the setting screen shown above is displayed you can

the

dial or the

minus (–) or plus (+) buttons to

change the setting. If you do not perform any operation for

a while, the setting screen will be exited automatically.

You can apply reverb, vibrato, and other effects to notes to

enhance their sound.

■ Effect Block Diagram

* When a tone with DSP (tone that uses a particular DSP)

that is not a Solo Synthesizer tone is selected. A tone with

DSP will have “DSP” next to its display name on the mixer

screen (page E-67) or performance editing screen (page

E-64).

■ Chorus and DSP Use Restrictions

Only one of the three effect types (Chorus, Normal DSP, Solo

Synthesizer DSP) can be enabled at any time.

Applying Effects to Notes

Sound

Source

(5) Master

Equalizer

Goes through (2), (3),

or (4). Also refer to

the “Chorus and DSP

Use Restrictions”

below.

Output

(1) Reverb

(2) Chorus

(3) Normal DSP

(4) Solo

Synthesizer

DSP

(1) Reverb Adds reverberation to make it sound like

you are playing in a room or in a hall.

(2) Chorus Combines multiple layers of the same note

to create a sound with more depth.

(3) Normal

DSP

A collection of versatile Normal DSP

effects help to enhance the sound of tones.

For example, distortion can be applied to

an electric guitar sound to make it sound

more powerful. There are 46 different

Normal DSP types, and the most

appropriate one for the selected tone is

applied automatically.

A DSP can be

edited and saved as a user DSP.

(4) Solo

Synthesizer

DSP

One of the elements that makes up a Solo

Synthesizer tones. See “(7) Total Block” in

the “Editable Solo Synthesizer Tone

Parameters” on page E-22. There are six

Solo Synthesizer DSP types. When you

edit a Solo Synthesizer DSP, it is saved as

part of a Solo Synthesizer user tone. You

cannot save it as a user DSP.

(5) Master

Equalizer

Adjusts the frequency characteristics of the

Synthesizer’s notes. The Master Equalizer

can be used to adjust the frequency and

gain of four frequency bands: low, mid1,

mid2, and high.

Under this condition:

This type of

effect is valid:

And effects are

applied to each

part like this:

Chorus Mode

• A tone other than

the Song Sequencer

is selected by Zone

Part 1, and the

Chorus is selected

by “Chorus/DSP

Select” (page E-38).

(2) Chorus Depends on the

mixer chorus

send value

(page E-68) and

the selected

tone chorus

send value

(page E-29).

Normal DSP Mode

• A tone other than

the Song Sequencer

is selected by Zone

Part 1, and the DSP

is selected by

“Chorus/DSP

Select” (page E-38).

(3) Normal DSP (3) is applied

only to parts

whose mixer

DSP line (page

E-68) is on.

Solo Synthesizer Tone

Mode

• Solo Synthesizer

tone selected by

Zone Part 1.

(4) Solo

Synthesizer

DSP

(4) is applied

only to Zone

Part 1 and parts

whose mixer

DSP line is on.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 95 96

Comments to this Manuals

No comments

Casio XW-P1 User's Guide Page 39

Comments to this Manuals

Related products and manuals for Synthesizer Casio XW-P1