Casio PX-5S User Manual download pdf (Page 21)

E-20

Using Built-in Tones (Tutorial)

02: Compressor

Compresses the input signal, which can have the effect of

suppressing level variation and can make it possible to sustain

dampened sounds longer.

Parameter Value Ranges:

1 :Attack (0 to 127)

Adjusts the attack amount of the input signal. A smaller value

causes prompt compressor operation, which suppresses the attack

of the input signal. A larger values delays compressor operation,

which causes the attack of the input signal to be output as-is.

2 :Release (0 to 127)

Adjusts the time from the point the input signal drops below a

certain level until the compression operation is stopped.

When an attack feeling is desired (no compression at the onset of

sound), set this parameter to as low a value as possible. To have

compression applied at all times, set a high value.

3 :Depth (0 to 0 to 127)

Adjusts compression of the audio signal.

4 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

Output volume changes in accordance with the Depth setting and

the characteristics of the input tone.

5 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

03: Limiter

Limits the input signal level so it does not rise above a preset level.

Parameter Value Ranges:

1 :Limit (0 to 127)

Adjusts the volume level of the limit at which limiting is applied.

2 :Attack (0 to 127)

Adjusts the attack amount of the input signal.

3 :Release (0 to 127)

Adjusts the time from the point the input signal drops below a

certain level until the limit operation is stopped.

4 :Wet Level (0 to 127)

Adjusts the level of the effect sound. Output volume changes in

accordance with the Limit setting and the characteristics of the

input tone. Use this parameter to correct for such changes.

5 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

04: Enhancer

Enhances the profiles of the low range and high range of the input

signal.

Parameter Value Ranges:

1 :Low Frequency (0 to 127)

Adjusts the low range enhancer frequency.

2 :Low Gain (0 to 127)

Adjusts the low range enhancer gain.

3 :High Frequency (0 to 127)

Adjusts the high range enhancer frequency.

4 :High Gain (0 to 127)

Adjusts the high range enhancer gain.

5 :Input Level (0 to 127)

Adjusts the input level.

6 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

7 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

05: Early Reflection

An effector that extracts early reflections from reverb.

Applies acoustic presence to notes.

Parameter Value Ranges:

1 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

2 :Feedback (0 to 127)

Adjusts the repeat of the reflected sound.

3 :Tone (0 to 127)

Adjusts the tone of the reflected sound.

4 :Input Level (0 to 127)

Adjusts the input level.

5 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

06: Phaser

Produces a distinctive pulsating, broad sound by using an LFO to

change the phase of the input signal and then mixes it with the

original input signal.

Parameter Value Ranges:

1 :Resonance (0 to 127)

Adjusts the strength of feedback

2 :Manual (–64 to 0 to +63)

Adjusts the reference phaser shift amount.

3 :LFO Rate (0 to 127)

Adjusts the LFO rate.

4 :Depth (0 to 127)

Adjusts the LFO depth.

5 :LFO Waveform (Sin, Tri, Random)

Selects the LFO waveform.

6 :Input Level (0 to 127)

Adjusts the input level.

7 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

8 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

07: Chorus

Gives notes depth and breadth.

Parameter Value Ranges:

1 :LFO Rate (0 to 127)

Adjusts the LFO rate.

2 :Depth (0 to 127)

Adjusts the LFO depth.

3 :LFO Waveform (Sin, Tri)

Selects the LFO waveform.

4 :Feedback (–64 to 0 to +63)

Adjusts the strength of feedback

5 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

6 :Polarity (–, +)

Inverts the LFO of one channel.

7 :Input Level (0 to 127)

Adjusts the input level.

8 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

08: Flanger

Applies wildly pulsating and metallic reverberation to notes. Selects

the LFO waveform.

Parameter Value Ranges:

1 :LFO Rate (0 to 127)

Adjusts the LFO rate.

2 :Depth (0 to 127)

Adjusts the LFO depth.

3 :LFO Waveform (Sin, Tri, Random)

Selects the LFO waveform.

4 :Feedback (–64 to 0 to +63)

Adjusts the strength of feedback

5 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

6 :Input Level (0 to 127)

Adjusts the input level.

7 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

09: Tremolo

Shifts the volume of the input signal using an LFO.

Parameter Value Ranges:

1 :LFO Rate (0 to 127)

Adjusts the LFO rate.

2 :Depth (0 to 127)

Adjusts the LFO depth.

3 :LFO Waveform (Sin, Tri, Tra)

Selects the LFO waveform.

4 :Wet Level (0 to 127)

Adjusts the level of the effect sound.

5 :Dry Level (0 to 127)

Adjusts the level of the direct sound.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 54 55

Comments to this Manuals

No comments

Casio PX-5S User Manual Page 21

Comments to this Manuals

Related products and manuals for Digital pianos Casio PX-5S