Casio DT-970M51E User's Guide

Handheld TerminalDT-970ESeriesUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal.

E-8Operating PrecautionsYour Handheld Terminal and its options are precision. Improper operation or rough handling can cause problems with data storag

E-9About the Waterproofi ng/Dustproofi ngThe DT-970 Series models are waterproof and dustproof.Waterproofi ng: Performance complies with the IPX7 level s

E-10Regulatory InformationEuropeProducts are for distribution within all member states of the EU.09840984Optional models HA-N60IO, HA-N62IO, HA-E60IO

E-11Accessories and OptionsPlease check the items in the box before using the Handheld Terminal for the fi rst time.• Alkaline AA batteries 2• Coin-

E-12General GuideHandheld Terminal (DT-970M50E/M51E)The illustration shows the DT-970M51E.ScreenReset SwitchPower ContactsIR PortR Trigger KeyUSB Port

E-13Barcode Reader PortLaser light is emitted from this window that reads bar codes.Indicator Three-color LED (red, green, blue). Shows the operatin

E-14Center Trigger KeyUsed to perform bar code reading.USB Port Connects the optional USB cable (HA-N81USBC).Buzzer Outputs operation confi rmation ton

E-15Ethernet Cradle (HA-N62IO), USB Cradle (HA-N60IO)The illustration shows the HA-N62IO.Left Top RightFront BackSelector Switch*Data CommunicationTer

E-16USB Client Port This port is used to transmit data and fi les (download, upload) by connecting the cradle to a PC using a USB cable (DT-380USB-A).

E-17Loading and Removing the BatteriesTwo types of battery are used in the Handheld Terminal. There are the main batteries used to operate the Handhel

BLUETOOTH is a registered trademark owned by Bluetooth SIG, Inc. and licensed to CASIO COMPUTER CO., LTD.eneloop is a registered trademark of Pana

E-18Loading the Main Batteries1. Turn the battery cover lock switches to the “FREE” position and remove the battery cover.2. Load the batteries, ensur

E-19Loading the Backup Battery1. Loosen the 2 screws and remove the battery cover by opening the notch with your fi ngernail.2. Load the battery from t

E-20Handling microSD CardsThe Handheld Terminal supports microSD card.Since the microSD card slot is located inside the battery compartment, fi rst rem

E-21Removing1. Make sure that the power on the terminal has been switched off. If the power is still on, press the power key to switch off.2. Remove t

E-22Performing Communications IR CommunicationIR communication can be used to transmit data between two Handheld Terminals.When performing IR communic

E-23Bluetooth® CommunicationBluetooth® interface can also be used to transmit data between two Handheld Terminals. With Bluetooth® the two Handheld Te

E-24Resetting the Handheld TerminalResetting the Handheld Terminal is the same as restarting a PC. Performing a reset causes all unsaved inputs and ed

E-25Warning LabelThe illustration shows the DT-970M51E.The label location differs depending on the model.This label is a warning and caution label for

E-26DT-970 Specifi cations Model: DT-970M50E/M51ECPU: 32bit CPUMemory: 8MB RAM, 32MB Flash ROM (user area: approx. 28MB)Display: 2.3-inch, 12

E-27Dimensional Drawings54.0mm(Display)(Display)(Grip)(Grip)52.0mm173.5mm25.0mm26.9mm

E-1ContentsSafety Precautions ...E-3Operating Precautions ...

E-28Connecting the USB Cradle (HA-N60IO) Power SupplyYou can use the optional USB cable (DT-380USB-A) to connect the USB Cradle to a computer and use

E-29Important!Water or other liquids on the data communication or power supply terminals can lead to an electric shock or fi re. Note also that soiling

E-30Specifi cations1. USBProtocol: USB Ver2.0 Full speedTransfer Rate: 12Mbps (max.)2. Power SupplyOutput to Handheld Terminal: 5V DC 0.5A (max.)3.

E-31Connecting the USB Cradle (HA-E60IO) Power SupplyBefore using the cradle, fi t the optional attachment kit (HA-N64AT).1. Make sure that the USB Cra

E-323. Connect the USB cable (DT-380USB-A) to the USB port on the back of the USB Cradle and then connect it to the personal computer.4. Line up the i

E-33Connecting the Ethernet Cradle (HA-N62IO) Power SupplyUse the separately sold AC adaptor (AD-S42120C) for the power supply of the Ethernet Cradle.

E-344. Before using the cradle ports, remove the caps from the ports. When using a LAN, connect one end of the LAN cable to the LAN port and the other

E-35Important!Always make sure to fi rst remove the 970 from the Ethernet Cradle when switching the selector switch.Water or other liquids on the data

E-36Adjusting the Laser Beam WidthYou can select the laser beam width used by the DT-970. Note that using this function may result in a laser beam wid

E-37Print this page at its actual size (not reduced) to adjust the laser beam width.Laser Beam Width Adjustment Bar Code

E-2Connecting the USB Cradle (HA-E60IO) Power Supply ...E-31Connecting the Ethernet Cradle (HA-N62IO) Power Supply ...

CASIO COMPUTER CO., LTD.6-2, Hon-machi 1-chomeShibuya-ku, Tokyo 151-8543, Japan2013 CASIO COMPUTER CO., LTD.

E-3Safety PrecautionsCongratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use

E-4 WarningDust and MoistureThough the Handheld Terminal is dust and water splash resistant, its options including the cradle are not. Keep loose meta

E-5Rechargeable Batteries CautionUse Panasonic “eneloop” rechargeable AA batteries. Do not use other types of rechargeable battery.Always charge the

E-6 CautionIncorrect use of the batteries could result in staining of the surroundings due to fl uid leakage, or could cause the batteries to burst, re

E-7Power Supply / AC Adaptor WarningDo not use the Handheld Terminal at a voltage other than the specifi ed voltage.Never modify, sharply bend, twist,