Casio STC-U10 User's Guide Page 53
- Page / 55
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
51
Symptom Cause and Required Action
Stamp printing
won’t start.
●
Windows XP:
Log in to the computer with an admin account and
then perform the steps below.
1. Click Start and then Control Panel.
2. Double-click the System icon.
3. Click the Hardware tab and then click the
Device Manager button.
4. Click the plus (+) icon next to USB Controllers
(Universal Serial bus Controllers).
USB is enabled when the USB controller and USB
route hub are displayed. If there is hub with multiple
USB chains, either connect the Printer’s USB cable to
another hub or try connecting a different device.
Check to make sure the cable is plugged into securely
and completely.
If the USB host controller and USB route hub
are not displayed, refer to your computer’s user
documentation or contact the manufacturer of your
computer for information about how to set up and
enable USB.
The stamp
layout
operation
completes
normally, but
nothing prints
on the stamp
sheet.
● No image or text in the stamp face layout.
Insert an image or text into the layout.
•
➜
Printed
stamps are
unclear.
I can’t print
clear stamps.
●
●
Dirt, dust, or other foreign matter on the stamp sheet
print head and/or the rubber roller.
Perform cleaning.
•
➜
I can’t print
stamps.
Power turns
off during
stamp printing.
●
●
You are using the wrong type of AC adaptor.
Use the specifi ed AC adaptor.
The stamp print head is very hot.
Wait for a while and then try performing the operation
again.
•
➜
•
➜
Symptom Cause and Required Action
I can’t
establish
a USB
connection
with a
computer.
● The USB cable is not connected securely.
Make sure that the USB cable is connected
correctly. If you still can’t establish a connection, try
disconnecting and re-connecting the cable.
•
➜
The USB driver is not installed on the computer.
Install the USB driver on the computer. If the above
steps don’t solve the problem, try connecting the USB
cable to a different USB port on the computer.
•
➜
Use the USB cable that comes with the STC-W10
Printer.
A sheet holder
is jammed and
won’t come
out.
● Shift the release lever on the bottom of the Printer to the
RELEASE side and then pull out the sheet holder.
RELEASE
PRINT
Next, return the release lever to the PRINT side and
perform printing again. If you experience problems using
the same sheet holder, use a new one.
Important!
Note the following while stamp printing is in progress.
Do not allow the sheet holder outlet slot to become
covered.
Do not touch the sheet holder.
Do not change the release lever position.
Do not disconnect or unplug the AC adaptor.
•
•
•
•
- STC-PC10 Application 1
- Important! 2
- Overview and Preparation 4
- Using This Manual 5
- Display screens 6
- Printer Models Supported by 7
- Introduction 7
- Starting Up and Exiting the 10
- Basic Operations 11
- Create from image button 12
- Create your own button 12
- Saved stamps folder button 12
- Control panel 13
- Navigation controls 13
- Menu bar 13
- Guidance 13
- Editing area 13
- Stamp preview image 14
- Using an Existing Stamp Face 15
- Selecting a stamp 16
- 3 Click the stamp size 17
- Previewing the stamp image 18
- 2 Click Next 19
- 1 Click the Print button 19
- 2 Click OK 20
- Computer to Create a Stamp 21
- (Create from image) 21
- 6 Adjust the applied effect 22
- 8 Print the stamp 22
- Next higher folder 23
- My pictures tab 23
- Desktop tab 23
- 1 Click the Size down ( 24
- 3 Click the Next button 25
- 2 Click the Next button 26
- Adjusting the extracted image 27
- 1 Select an effect 28
- 2 Adjust the effect 29
- 4 Click the Next button 30
- Creating an Original Stamp 32
- Design (Create your own) 32
- 4 Print the stamp sheet 33
- 1 Click the Item tab 34
- 2 Click the + (Add) button 35
- 1 Click the Frames tab 37
- 1 Click the Text tab 39
- 2 Enter text 39
- 1 Click the Draw tab 41
- 3 Click Next 42
- Recalling a Saved Stamp 44
- (Saved stamps folder) 44
- Stamp folder 45
- Photo folder 45
- NextDelete 45
- Editing the stamp face 46
- 2 Click the Save button 47
- Confi guring STC-PC10 48
- Application Properties 48
- 4 Click OK 49
- 3 Click OK 49
- Using Help 50
- STC-PC10 51
- Application 51
- Appendix 51
- Software Troubleshooting 52
- Error Messages 54
- CASIO COMPUTER CO., LTD 55
Related products and manuals for Print & Scan Casio STC-U10
Print & Scan Casio KL-120 User's Guide
(32 pages)
(32 pages)
Print & Scan Casio STC-U10 User's Guide
(50 pages)
(50 pages)
Print & Scan Casio KL-C500 User's Guide
(52 pages)
(52 pages)
Print & Scan Casio KL-8200 User's Guide
(36 pages)
(36 pages)
Print & Scan Casio MEP-U10 User's Guide
(30 pages)
Print & Scan Casio KL-8100 User's Guide
(31 pages)
(31 pages)
Print & Scan Casio IT-3100 User's Guide
(75 pages)
(75 pages)
Print & Scan Casio MEP-U10 User's Guide
(30 pages)
(30 pages)
Print & Scan Casio IT-9000 Series Manual
(79 pages)
(79 pages)
Print & Scan Casio KL-7000 Owner's Manual
(81 pages)
(81 pages)
Print & Scan Casio KL-8200 User Manual
(12 pages)
(12 pages)
Print & Scan Casio LPCW-50 User's Guide
(85 pages)
(85 pages)
(89 pages)
Print & Scan Casio STC-U10 User Manual
(51 pages)
Pro-Form PFTL79108.0 manuals
Owner’s manuals and user’s guides for Treadmills Pro-Form PFTL79108.0.
We providing 1 pdf manuals Pro-Form PFTL79108.0 for download free by document types: User Manual
Comments to this Manuals