Casio 3406 Technical Information download pdf (Page 7)

Operation Guide 2894

Countdown start time

You can set a countdown start time in the range of one minute to 60 minutes,

in one-minute increments.

Auto-repeat

Whenever zero is reached, the watch beeps and auto-repeat automatically

restarts the countdown from the countdown start time you set. When the

countdown reaches zero while auto-repeat is turned off, the watch will beep

and then display the countdown start time (without restarting the countdown).

Auto repeat will repeat up to 10 times.

Progress Beeper

When the progress beeper is turned on, the watch beeps at minute 10, 5, 4,

3, 2, and 1, of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2,

and 1 of the final minute of the countdown.

To configure countdown start time and auto repeat settings

1. While the countdown start time is on the

display in the Countdown Timer Mode, hold

down E until the minute setting of the

countdown start time starts to flash, which

indicates the setting screen.

• If the countdown start time is not displayed,

use the procedure under “To use the

countdown timer” to display it.

2. Press D to toggle between the countdown

starting time setting screen and the auto

repeat setting screen.

3. Perform the following operations, depending on which setting is currently

selected on the display.

• While the minute setting is flashing, use C (+) or A (–) to change it.

• While the auto-repeat on/off setting (

or ) is flashing on the

display, press C to toggle auto-repeat on (

) and off ( ).

4. Press E to exit the setting screen.

To turn the progress beeper on and off

Pressing A while the countdown start time is on

the display or while a countdown timer operation

is in progress in the Countdown Timer Mode

toggles progress beeper operation on (

displayed) and off ( not displayed).

To use the countdown timer

Press C while in the Countdown Timer Mode to start the countdown timer.

• When the countdown reaches zero, the alarm sounds for five seconds or

until you stop it by pressing any button.

• Press C while a countdown operation is in progress to pause it. Press C

again to resume the countdown.

Progress beeper on

indicator

• The countdown timer operation continues even if you exit the Countdown

Timer Mode.

• To completely stop a countdown operation, first pause it (by pressing C),

and then press A. This returns the countdown time to its starting value.

• Frequent use of auto-repeat and the alarm can run down battery power.

To set an alarm time

1. In the Alarm Mode, use C and A to scroll

through the alarm screens until the one whose

time you want to set is displayed.

2. Hold down E until the hour setting of the alarm time start to flash, which

indicates the setting screen.

• This automatically turns on the alarm.

3. Press D to move the flashing between the hour and minute settings.

4. While a setting is flashing, use C (+) and A (–) to change it.

• When setting the alarm time using the 12-hour format, take care to set

the time correctly as a.m. (no indicator) or p.m. (P indicator).

5. Press E to exit the setting screen.

AL1

SIG

AL2

AL3

AL4

AL5

Alarm Operation

The alarm sounds in all modes at the preset time for about 10 seconds, or

until you stop it by pressing any button.

To test the alarm

In the Alarm Mode, hold down C to sound the alarm.

To turn an alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, use C and A to select an alarm or the Hourly Time

Signal.

2. When the alarm or the Hourly Time Signal you want to is selected, press

B to turn it on and off.

Indicates alarm is ON.

Indicates Hourly Time Signal is ON.

• The alarm on indicator (

) and the Hourly Time Signal on indicator ( )

are shown on the display in all modes while these functions are turned on.

• If any alarm is on, the alarm on indicator is shown on the display in all

modes.

Illumination

The display of the watch is illuminated using an

EL (electro-luminescent) panel for easy reading

in the dark. The watch’s auto light switch

automatically turns on illumination when you

angle the watch towards your face.

• The auto light switch must be turned on

(indicated by the auto light switch on indicator)

for it to operate.

• You can specify 1.5 seconds or 2.5 seconds as

the illumination duration.

• See “Illumination Precautions” for other

important information about using illumination.

Auto light switch on

indicator

To turn on illumination manually

Press L in any mode to illuminate the display.

• The above operation turns on illumination regardless of the current auto

light switch setting.

• Illumination is disabled while the Digital Compass, Barometer/

Thermometer, or Altimeter Mode setting screen is on the display.

Countdown Timer

You can set a countdown timer start time in the

range of one minute to 60 minutes. An alarm

sounds when the countdown reaches zero. An

auto-repeat feature causes the countdown to

restart automatically when the end of a

countdown is reached, and a progress beeper

signals the progress of the countdown.

• All of the operations in this section are

performed in the Countdown Timer Mode,

which you enter by pressing D.

Configuring the Countdown Timer

The following are the settings you should

configure before actually using the countdown

timer.

• Countdown start time

• Auto-repeat on/off

• Progress beeper on/off

Seconds

Minutes

Timekeeping

Mode time

Alarms

You can set five independent daily alarms. When

an alarm is turned on, the alarm tone sounds

when the alarm time is reached.

You can also turn on an Hourly Time Signal,

which will cause the watch to beep twice every

hour on the hour.

• The alarm number (

AL1 through

AL5 ) indicates an alarm screen. SIG is

shown when the Hourly Time Signal screen is

on the display.

• When you enter the Alarm Mode, the data you

were viewing when you last exited the mode

appears first.

• All of the operations in this section are

performed in the Alarm Mode, which you enter

by pressing D.

Alarm time

(Hour : Minutes)

Alarm number

Alarm on indicator

Hourly time signal on

indicator

Timekeeping

Mode time

1 2 3 4 5 6 7 8 9 10 11 12

Operation Guide 2894 1

Comments to this Manuals

No comments

Casio 3406 Technical Information Page 7

Comments to this Manuals