Casio 2575 User Manual download pdf (Page 2)

USER’S GUIDE 2575

• The following examples illustrate how you can calculate values for this setting.

239 steps required to run around a 300-meter track.

300 (meters)

239 (steps) = 1.255 (approximately 125 cm)

239 steps required to run around a 330-yard track.

330 (yards)

239 (steps)

36 = 49.70 (approximately 50 inches)

Setting Range

40 to 190 cm

16 to 76 in

Setting Increment

5 cm

2 in

Distance Unit

Kilometers (km)

Miles (mi)

Stride Length Unit

Centimeters (XM)

Inches (Yn)

To configure your basic data

1. While the Stopwatch Mode screen shows all zeros

(

0 H

00'00''00), hold down B until the pacer value

appears flashing on the display. This indicates the

setting screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

3. When the setting you want to change is flashing, use

D and A to change it as described below.

Stride length unit

Pacer value Pacer signal

Stride length

Setting

Pacer value

Pacer signal

Stride length

Stride length unit

Screen Button Operations

Use D (+) and A (–) to change the setting.

• Selecting xxx disables the pacer signal.

Press D to toggle the pacer signal on (ON)

and off (OFF).

Use D (+) and A (–) to change the setting.

Press D to toggle between centimeters (XM)

and inches (Yn).

• When the pacer signal is turned on, the pacer signal sounds in accordance with the

pacer value while the pacer signal or pacer value setting screen is on the display.

4. Press B to exit the setting screen.

• If you find that the stride length unit won’t change reset the cumulative total to all

zeros.

To turn the pacer signal on and off

1. While the Stopwatch Mode screen shows all zeros

(

0 H

00'00''00), hold down B until the pacer value

appears flashing on the display. This indicates the

setting screen.

2. Press C once to display the pacer signal setting

screen.

3. Press D to toggle the pacer signal on (ON) and off

(OFF).

• A pacer signal on indicator (

) appears when this

setting it turned on.

4. Press B to exit the setting screen.

Recall Mode

Use the Recall Mode to recall and delete records stored

by the Stopwatch Mode.

• Stopwatch records are stored in “logs” that are created

automatically by the watch. See “Memory Management”

for more information.

• The title screen of the newest log appears first whenever

you enter the Recall Mode.

• Log numbers are automatically assigned in sequence,

starting from 01.

• All of the operations in this section are performed in the

Recall Mode, which you enter by pressing C.

To recall stopwatch records

In the Recall Mode, use B to scroll through the log title

screens, starting from the newest one, as shown below.

When the title screen of the log you want is displayed, use

D and Ato cycle through the records contained in the log.

Distance covered

Log number

Creation date

(Month – Day)

Log Title Screen

• The cumulative total screen shows the total distance since the last cumulative total

distance reset.

Press A.

▲

Press D.

Split time

Lap/Split number

BEST indicator

▲

Cumulative Total Screen

▲

Press B.

Log Title Screen

Stopwatch Record

Screen

Best Lap Time

Screen

Lap time

▲

• The locations of the lap time and split time (middle or bottom of the display) in the

Stopwatch Record screen are determined by the display format you last selected in

the Stopwatch Mode.

• The BEST indicator identifies the record that contains the best lap time in the log.

• If a best lap time record is deleted automatically when the log becomes full, the

BEST indicator will not be transferred to the record with the next best lap time. See

“Memory Management” for more information about automatic deletion of records.

• The unit of measurement used for the distance calculation depends on the unit you

select for your stride length as shown in the table below. See “To configure your

basic data” for more information.

Selected Stride Unit Distance Unit

XM (centimeters) km (kilometers)

Yn (inches) mi (miles)

To delete a log

1. In the Recall Mode, display the title screen of the log you want to delete.

• See “To reset the cumulative total screen” below for information about what

happens when you select the cumulative total screen here.

2. Hold down A and D until the watch beeps and

CLR stops flashing on the

display.

• This deletes the log and all the records inside it. Deleting a log does not change the

cumulative total distance value.

To reset the cumulative total screen

1. In the Recall Mode, display the cumulative total screen.

2. Hold down A and D until the watch beeps and

CLR stops flashing on the

display.

• This resets the cumulative total distance to zero, without deleting any logs or

records. A new cumulative total will start with the next stopwatch operation you

perform.

Countdown Timer

You can set the countdown timer within a range of one

minute to 100 hours. An alarm sounds when the

countdown reaches zero.

• You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• Countdown timer functions are available in the

Countdown Timer Mode, which you can enter using C.

To set the countdown start time

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down B until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

diplay it.

2. Press C to move the flashing between the hour and

minute settings.

3. Use D (+) and A (–) to change the flashing item.

• To set the starting value of the countdown time to 100

hours, set 0:00.

4. Press B to exit the setting screen.

To use the countdown timer

Press A while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value when the alarm sounds.

• Press A while a countdown operation is in progress to pause it. Press A again to

resume the countdown.

• To completely stop a countdown operation, first pause it (by pressing A), and then

press D. This returns the countdown time to its starting value.

Hours

Minutes

Seconds

Timekeeping Mode time

To turn auto-repeat on and off

While the countdown start time is displayed on the

Countdown Timer Mode screen, hold down D for about

two seconds to toggle auto-repeat on (

displayed) and

off (

not displayed).

• When auto-repeat is turned on, the alarm sounds and

countdown starts again whenever the countdown

reaches zero. You can stop the countdown by pressing

A, and manually reset to the countdown start time by

pressing D.

• Auto-repeat timing repeats up to seven times.

Alarms

You can set five independent Daily Alarms. When an

alarm is turned on, the alarm tone sounds when the alarm

time is reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other four are

one-time alarms.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• There are five alarm screens numbered 1 through 5.

The hourly time signal screen is indicated by :00.

• All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm number

Alarm time

(Hour : Minutes)

Timekeeping Mode time

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2

through 5 can be used as one-time alarms only.

• The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down B until the hour setting of the alarm time

starts to flash. This indicates the setting screen.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and A (–) to change it.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (PM indicator).

5. Press B to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze

alarm, the alarm operation is performed a total of seven times, every five minutes, until

you turn the alarm off or change it to a one-time alarm.

x1 x2

:00 x5

1 2 3 4

USER’S GUIDE 2575 1

Comments to this Manuals

No comments

Casio 2575 User Manual Page 2

Comments to this Manuals

Besa-lighting Kani (Linear Pendants) manuals

More products and manuals for Lighting Besa-lighting

Casio 2575 User Manual Page 2

Comments to this Manuals

Related products and manuals for Watches Casio 2575

Besa-lighting Kani (Linear Pendants) manuals

More products and manuals for Lighting Besa-lighting