Casio 3193 User Manual download pdf

Operation Guide 3193 3200

MO0908-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Warning!

• The measurement functions built into this watch are not intended for taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonable representations only.

• The Moon phase indicator and tide graph data that appear on the display of this

watch are not intended for navigation purposes. Always use proper instruments

and resources to obtain data for navigation purposes.

• This watch is not an instrument for calculating low tide and high tide times. The

tide graph of this watch is intended to provide a reasonable approximation of

tidal movements only.

• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any

claims by third parties that may arise through the use of this watch.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a rechargeable battery. Leaving or using the

watch where it is not exposed to light causes the battery

to run down. Make sure the watch is exposed to light as

much as possible.

• When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

• You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is covered only partially.

Bright Light

Solar cell

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

• The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

• The actual level at which some functions are disabled depends on the watch model.

• Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a

single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately about 8 hours exposure to indoor fluorescent lighting

• Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

• See “Power Saving Function” for more information.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage

or loss suffered by you or any third party arising through the use of this product or

its malfunction.

About This Manual

• Depending on the model of your watch, display text appears either as dark figures

on a light background (Module 3193), or light figures on a dark background (Module

3200). All of the illustrations in this manual show Module 3193.

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

Module 3193 Module 3200

Countdown Timer Mode Stopwatch Mode

Alarm Mode

▲

World Time Mode

▲

General Guide

• Press C to change from mode to mode.

• In any mode (except when a setting screen is on the display), press L to illuminate

the display.

Timekeeping Mode

Press C.

▲

Tide/Moon Data Mode

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

• This watch is designed to pick up the time calibration signals transmitted in Germany

(Mainflingen), England (Anthorn), the United States (Fort Collins), China (Shangqiu),

and Japan (Fukushima, Fukuoka/Saga).

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration

signal. You also can perform a manual procedure to set the time and date, when

necessary.

• The first thing you should do after purchasing this watch is to specify your

Home City (the city where you normally will use the watch). For more

information, see “To specify your Home City” below.

• When using the watch outside the areas covered by the time signal transmitters, you

will have to adjust the current time setting manually as required. See “Timekeeping”

for more information about manual time settings.

• The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of

Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press D (east) and B (west) to select the city code

you want to use as your Home City.

LIS, LON : Lisbon, London

MAD, PAR, ROM, BER, STO : Madrid, Paris,

Rome, Berlin, Stockholm

ATH : Athens

MOW : Moscow

HKG, BJS, TPE : Hong Kong, Beijing, Taipei

SEL, TYO : Seoul, Tokyo

HNL : Honolulu

ANC : Anchorage

YVR, LAX: Vancouver, Los Angeles

YEA, DEN : Edmonton, Denver

MEX, CHI : Mexico City, Chicago

NYC : New York

YHZ : Halifax

YYT : St.Johns

City code

PM indicator

Seconds

Hour : Minutes

3. Press A to exit the setting screen.

• Normally, your watch should show the correct time as soon as you select your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation (in the middle of the night). You also can perform manual receive or you

can set the time manually.

• The watch will receive the time calibration signal automatically from the applicable

transmitter (in the middle of the night) and update its settings accordingly. For

information about the relationship between city codes and transmitters, see

“Important!” under “Time Calibration Signal Reception” and “Transmitters”.

• See the maps under “Approximate Reception Ranges” for information about the

reception ranges of the watch.

• You can disable time signal reception, if you want. See “To turn auto receive on and

off” for more information.

• Under factory default settings, auto receive is turned off for all of the following city

codes: MOW (Moscow), HNL (Honolulu), and ANC (Anchorage). For details about

turning on auto receive for these city codes, see “To turn auto receive on and off”.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

• Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to

6 times a day (5 times a day for the Chinese calibration signal). When any auto

receive is successful, the remaining auto receive operations are not performed. For

more information, see “About Auto Receive”.

• Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see “To perform manual receive”.

1 2 3 4 5 6 7 8

Operation Guide 3193 3200 1

Summary of Contents

Page 1 - Operation Guide 3193 3200

Operation Guide 3193 32001MO0908-EAGetting AcquaintedCongratulations upon your selection of this CASIO watch. To get the most out of yourpurchase, be

Page 2

Operation Guide 3193 32002Important!• When getting ready to receive the time calibration signal, position the watch asshown in the nearby illustration

Page 3

Operation Guide 3193 32003• If the latest reception fails but a previous reception wassuccessful, an indicator () will be on the display.• The watch w

Page 4

Operation Guide 3193 32004To toggle a city code time between Standard Time and Daylight Saving Time1. In the World Time Mode, use D and B to display t

Page 5

Operation Guide 3193 32005About the Auto Light SwitchTurning on the auto light switch causes illumination to turn on, whenever you positionyour wrist

Page 6

Operation Guide 3193 320064. When the timekeeping setting you want to change is flashing, use D or B tochange it as described below.Change the city co

Page 7

Operation Guide 3193 32007Power Saving FunctionWhen turned on, the Power Saving function enters asleep state automatically whenever the watch is left

Page 8

Operation Guide 3193 32008City Code TablePago PagoHonoluluAnchorageVancouverLos AngelesEdmontonDenverMexico CityChicagoNew YorkSantiagoHalifaxSt. John

Related models: 3200

Comments to this Manuals

No comments

Casio 3193 User Manual

Browse online or download User Manual for Clock Casio 3193. Casio 3193 User Manual

Summary of Contents

Related models: 3200

Comments to this Manuals

Related products and manuals for Clock Casio 3193