Casio PX-5S User Manual download pdf (Page 35)

E-34

Using the Stage Setups (Tutorial)

Master Effect Edit >Ent

Master effect parameter. This is a group of editable master effect parameters

(page E-23). For details about group items, see “Editable MASTER

Parameters” (page E-23).

Compressor Edit

>Ent

Compressor edit. This is a group of editable compressor parameters within

master effects.

Equalizer Edit >Ent

Equalizer edit. This is a group of editable equalizer parameters within

master effects.

Common Edit >Ent This is a group of editable pedal, PRN, and NPRN parameters.

Tempo

Tempo. Adjusts the phrase playback speed. You also can change the phrase

playback tempo using the

(TEMPO) button.

20 - 255

Phrase Phrase number. Selects the phrase of the Phrase Sequencer (page E-29). U000 - U999

Arpeggio

Preset arpeggio type selection. See “To use the Arpeggio Function” in the

separate USER’S GUIDE (Basics).

Off, On, Hold

Hammer Response

Hammer response. Adjusts hammer response within the range of 0 (fast) to

7 (slow).

0 - 7

Knob1 Edit >Ent

Knob 1 (Knob 1 edit). This is a group of

(K1) knob editable parameters.

Editing can be performed even when the “Knob 1 Enable” setting is “Off”.

Target

Target. Selects the parameters to be controlled by a controller. For example,

the “CC67:Soft” setting specifies a soft pedal effect.

• Two targets can be specified for a single controller. Use the

(ZONE)

minus (–), plus (+) buttons to switch between Target 1 and Target 2.

No Assign: No target specified.

CC00 to CC97: MIDI control change*

NRPN, RPN: MIDI NRPN and RPN parameters*

Ch.Pressure: MIDI channel pressure*

Tempo: Tempo setting (page E-30)

EQ Low Gain - EQ High Gain: Master EQ >Low Gain - High Gain (page

E-23)

DSP Bypass: Temporarily bypasses the DSP of the currently selected zone.

Ext.Volume: Control the External Volume value.

Layer Detune: Layer detune (page E-17)

Layer1 Volume - Layer6: Tone parameter settings of each layer

• The following can be assigned: Volume (Volume), Pan (panning), OctShift

(octave shift), DspOnOff (DSP on/off), LfoPitch (LFO pitch), LfoFiltr (LFO

filter), LfoAmp (LFO amp). For details about each setting, see the editable

parameters under “Using Built-in Tones (Tutorial)” on page E-10.

Dsp Param 1-16: DSP parameters

Pedal1 On Rate, Pedal1 Off Rate, Pedal2 On Rate, Pedal2 Off Rate: on value,

on rate, off value, off rate for each pedal*

Arp Hold On/Off: Arpeggio hold setting*

Song Str/Stp: Song sequencer playback start/stop*

Phrase Str/Stop: Phrase playback start/stop*

Audio Str/Stop: Audio playback start/stop*

Refer to the cell to the

left.

Min Value Minimum value. Controller minimum output value setting. 0 - 127

Max Value Maximum value. Controller maximum output value setting. 0 - 127

Knob2-4 Edit >Ent

Knob 2 to 4 (Knob 2 to 4 edit). This is a group of

Knob (K2) through (K4)

editable parameters. Editing can be performed even when the “Knob 2-4

Enable” setting is “Off”. Details of editable parameters are the same as

“Knob1 Edit >Ent”, above.

Display Text Description Settings

*1 For details about each setting, see the MIDI Implementation Chart

(http://world.casio.com/) and/or MIDI documentation.

*2 After selecting these setting items, press the

(ENTER) button again

and then adjust the items below.

MSB: 63H for NRPN, 65H for RPN (Setting range: 000 to 127)

LSB: 62H for NRPN, 64H for RPN (Setting range: 000 to 127)

Send Data: Specifies whether knob operation controls MSB or LSB

value. (Settings: MSB, LSB)

*3 This setting is not supported for Damper/Pedal 1 (Pedal 1) or Pedal 2.

This setting is supported for Damper/Pedal 1 (Pedal 1) and Pedal 2 only.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 54 55

Comments to this Manuals

No comments

Casio PX-5S User Manual Page 35

Comments to this Manuals

Related products and manuals for Digital pianos Casio PX-5S