Casio DT-X5 Series User Manual

Handheld TerminalESeriesUser’s GuideBe sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal. After reading

E-8Safety PrecautionsWarning• Never place the battery pack in a microwave oven or any other high-voltagedevice. Doing so creates the danger of battery

E-9AC Power SupplyWarning• Do not use the Handheld Terminal at a voltage other than the specifiedvoltage. Also, do not connect the Handheld Terminal t

E-10Safety PrecautionsAC AdaptorCaution• The housing of the AC adaptor can become warm during normal use.• Take normal precautions against electric sh

E-11Operating PrecautionsYour Handheld Terminal and its options are precision digital instruments. Improperoperation or rough handling can cause probl

E-12Important• The contents of this guide are subject to change without notice.• Note that CASIO COMPUTER CO., LTD. shall not be held liable to you or

E-13GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (notapplicable to other areas).NOTICEThis equipment has been tested and foun

E-14Product description / Intended useEU/EFTA member states intended for use EU: Austria, Belgium, Denmark, Finland, France,Germany, Greece, Ireland,

E-15Products are for distribution within all member states of the EU.DT-X5M10E/DT-X5M30E/DT-X5M30U; DT-X5M10R/DT-X5M30R/DT-X5M30UR;The folowing Notifi

E-16ContentsSafety Precautions ... 1Operating Precautions ...

E-17Resetting the Handheld Terminal ... 44Reset and Full Reset (Memory Initialization)

• This product includes BRYCEN Co., Ltd’ s B-RAPPORE Stack, which use is governedby a licence granted by BRYCEN Co., Ltd.• BLUETOOTH is a trademark ow

E-18Install the mainbatteryBefore Getting StartedBe sure to perform the following steps before using the Handheld Terminal for the firsttime.Handheld

E-19Install the main batteryWhen Using the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U only)1. Install the AA size alkaline batteries.1

E-20When Using the Battery PackCharging is required when using the battery pack (HA-A20BAT or DT-5025LBAT) soldseparately.Use the Dual Battery Charger

E-213 Return the main battery cover to itsoriginal position as shown in theillustration, and return the two mainbattery pack cover lock switches to th

E-22Handheld Terminal System ConfigurationOptionsDT-X5 SeriesHA-A60IOHA-A61IOBridge Satellite Cradle (HA-A61IO)Bridge Basic Cradle (HA-A60IO)Cradle-ty

E-23HA-A20BAT(Battery Pack)DT-5025LBAT(Large-capacity Battery Pack)Battery PackDT-891WHRequiredScrewsWall Mount UnitDual Battery ChargerDT-5022CHGRequ

E-24CablesDT-887AXADT-888RSCDT-380USBBridge Satellite Cradle Cable/RS-232C Dsub-9Pin (Female)RS-422 Modular CableUSB CableHandheld Terminal System Con

E-251 Indicator 12 Indicator 23 LCD Panel4 Power Key5 L Key6 R Key7 Cursor Key8 Multi Key9 Numeric Keys10 Execute KeyThis indicator is green when char

E-2611 Function Keys12 IR Port13 Power Contacts14 CLR Key15 Fn Key16 Main Battery CoverLock Switches17 R Trigger Key18 L Trigger Key19 Wrist Strap Hoo

E-27Replacing the BatteryYour Handheld Terminal uses two types of battery: main battery and a memory backupbattery.AA size alkaline batteries (DT-X5M1

E-1WarningCautionDangerSafety PrecautionsCongratulations upon your selection of this CASIO product. Be sure to read thefollowing Safety Precautions be

E-28Replacing the BatteryReplacing the AA size Alkaline Batteries (DT-X5M10E/DT-X5M30E/DT-X5M30U only)1. Make sure the Handheld Terminal is turned off

E-29To replace the battery pack1. Make sure that the Handheld Terminal is turned off.If the power is on, press the power key to turn it off.2. Turn ov

E-30Replacing the Battery4. Remove the battery pack by pulling up onthe battery pack removal tape.5. Install a charged battery pack in theHandheld Ter

E-31Loading the large-capacity battery pack into the Handheld TerminalAfter loading the large-capacity batterypack, you need to use the special large-

E-32Removing and Installing the Alkaline BatteryHolder (DT-X5M10E/DT-X5M30E/DT-X5M30U only)Removal ProcedureWhen using a battery pack, first remove th

E-3312211Installation ProcedureWhen using AA size alkaline batteries, install the alkaline battery holder according to thefollowing procedure.1. Make

E-34Attaching the Wrist StrapBe sure to attach the wrist strap and use it to protect against dropping the HandheldTerminal when carrying it around.Att

E-35Configuring Handheld Terminal SettingsAdjusting Display ContrastPerform the following steps to adjust display contrast to make display more vivid

E-36Using the Laser Scanner(DT-X5M10E/DT-X5M10R only)1. After turning on the power, position thelaser scanner close to a bar code and thenpress the Tr

E-37Warning Label• This label is a warning label for Class 2 laser products thatcomply with IEC60825-1+A2:2001CAUTION• Use of controls or adjustments

E-2Safety PrecautionsWarningForeign Objects• Should any foreign matter get into the Handheld Terminal and its options,immediately turn off the power a

E-38Using the C-MOS Imager(DT-X5M30E/DT-X5M30R/DT-X5M30U/DT-X5M30UR only)1. Turn on the Handheld Terminal, position its C-MOS Imager reader port near

E-39Warning Label• This label is a warning label for Class 2 laser products that comply withIEC60825-1+A2:2001CAUTION• Use of controls or adjustments

E-40Adjusting Laser Emission Width(DT-X5M10/DT-X5M10R only)This Handheld Terminal is able to adjust the emission width of laser light. Adjust theHandh

E-41Emission Width Adjustment Bar codeImportant!• An error message is displayed when emission width has not been adjustedproperly. Repeat the adjustm

E-42Performing CommunicationIR CommunicationIR communication can be used to transfer data between two Handheld Terminals.When performing IR communicat

E-43BluetoothTM CommunicationBluetoothTM protocol can also be used to transfer data between two Handheld Terminals.With BluetoothTM, the two Handheld

E-44Resetting the Handheld TerminalReset and Full Reset (Memory Initialization)ResetResetting the Handheld Terminal is the same as restarting a comput

E-45If reset finds a memory problemA message like the one shown below appears on the display when the reset operationdiscovers a memory problem.When t

E-46DT-X5 Specifications1. Handheld TerminalModel: DT-X5M10E, DT-X5M10R, DT-X5M30E, DT-X5M30R,DT-X5M30U, DT-X5M30URCPU: 32-bit RISC typeMemory: 16MB R

E-477. PowerMain power supply: Two AA size alkaline batteriesHA-A20BAT battery packDT-5025LBAT large-capacity battery packBackup power supply: Recharg

E-3CautionForeign Objects• Take care to ensure that metals or combustible objects are not inserted intothe openings of the Handheld Terminal and its o

E-48WeightDT-X5M10E/ Approx. 245 g (when HA-A20BAT battery pack is installed)DT-X5M30E/DT-X5M30UDT-X5M10R/ Approx. 250 g (when HA-A20BAT battery pack

E-491 2 3 451511121413109867BottomFrontRightBackTopFall protect coverAccessoryUsing the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60

E-50Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)1 USB Port2 RS-232C Port(HA-A61IO only)3 RS-422C Port(HA-A61IO only)4 A

E-51Connecting the AC Adaptor and Connecting to ComputerUse the AC adaptor sold separately from the Bridge Satellite Cradle/Bridge Basic Cradlefor the

E-52Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)5. Making sure that their two IR ports come into contact with each othe

E-53Removing the Fall ProtectorThe Bridge Satellite Cradle and Cradle-type Battery Charger Fall Protector can also beremoved. However, it is recommen

E-54Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)Configuring DIP Switch Settings (HA-A61IO)Dismounting the bottom cover

E-55Using Wall Mount UnitThe following procedure explains how to use the optional wall mount unit (DT-891WH)to configure the Bridge Satellite Cradle/B

E-56Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)4. Hook the upper wall mount unit hole ontothe upper screw.5. Drive the

E-57Connecting Multiple Bridge Satellite Cradles (HA-A61IO)Use the modular cable for the connections.You can daisy chain multiple BridgeSatellite Crad

E-4Safety PrecautionsThis wireless transmitter uses the 2.4 GHz band. It employs the FH-SSmodulation system and has an interfering range of 20 m.This

E-58Using the Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle (HA-A60IO)Bridge Satellite Cradle (HA-A61IO)/Bridge Basic Cradle(HA-A60IO) Specif

E-59Using the Cradle-type Battery ChargerThe optionally available Cradle-type Battery Charger (HA-A30CHG) lets you charge theHandheld Terminal’s batte

E-60Using the Cradle-type Battery Charger1 AC Adaptor Jack2 Wall Mount UnitFastening Plate3 Terminal DetectSwitch4 Power Contacts5 Power IndicatorLamp

E-61Connecting the AC Adaptor for Cradle-type Battery ChargerUse the special AC adaptor (sold separately) for the Cradle-type Battery Charger toconnec

E-62Using Wall Mount UnitTo wall mount the Cradle-type Battery Charger, use the same procedure as that describedfor the Bridge Satellite Cradle (HA-A6

E-63Using the Dual Battery ChargerThe optionally available Dual Battery Charger (DT-5022CHG) allows for parallelcharging of two rechargeable battery p

E-64Using the Dual Battery Charger1 Charge IndicatorLamp2 AC Adaptor Jack3 Dual BatteryCharger ConnectionPort4 Connection BracketAttachment HolesThis

E-65Charging a Battery Pack1. Plug the optional AC adaptor into the ACadaptor jack of the Dual Battery Charger.2. Plug the other end of the AC adaptor

E-66Using the Dual Battery ChargerConnecting Multiple Dual Battery ChargersYou can connect up to three Dual Battery Chargers. Doing so makes it possib

E-67Dual Battery Charger (DT-5022CHG) Specifications1. ModelDT-5022CHG2. ChargingCharging System: Fixed-voltage (with current limiter)Charge Time: App

E-5Alkaline Battery Handling PrecautionsDanger• Since there is the risk of blindness and other serious disorders when alkalinebattery fluid enters the

E-68Using Rechargeable Battery PackYour Handheld Terminal supports use of two battery pack types of different capacity. Youcan select the one that bes

E-69MemoDT-X5_E_P59_69.p65 04.7.14, 6:05 PM69

E-70MemoDT-X5_E_P59_70.p65 04.8.5, 3:50 PM70

DT-X5_E_Hyo_1_4.p65 04.7.14, 6:00 PM2

E-6Safety PrecautionsCaution• Promptly remove worn out batteries from the Handheld Terminal. Allowingworn out batteries to remain installed in the Ha

E-7Optional Lithium-ion Battery PackDanger• Never allow the battery pack to become wet. Water can create the danger ofbattery pack heat emission, expl